Checking the MortiSafe Pro core unit - Revision history

Mortice at 19:05, 22 March 2015

2015-03-22T19:05:26Z

← Older revision		Revision as of 19:05, 22 March 2015
Line 5:		Line 5:
	* An aerial which should be screwed into the end of the wifi unit		* An aerial which should be screwed into the end of the wifi unit
	* A USB power cable with clips half way along it		* A USB power cable with clips half way along it
	* A micro ~~USB~~ adapter in a plastic cover. You shouldn't need this unless you have to do an upgrade in future.		* A micro SD adapter in a plastic cover. You shouldn't need this unless you have to do an upgrade in future.

	[[File:MSP_BoardCloseup.JPG\|700px]]		[[File:MSP_BoardCloseup.JPG\|700px]]

Mortice at 21:56, 28 February 2015

2015-02-28T21:56:38Z

← Older revision		Revision as of 21:56, 28 February 2015
Line 13:		Line 13:
	# Screw the aerial into the wifi unit and plug that into the core unit (any socket)		# Screw the aerial into the wifi unit and plug that into the core unit (any socket)
	# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting		# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting
			# The relay unit has 2 little red 'jumper connectors', they should be on the board in the position indicated on the picture above
	# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which color goes into which screw) so ensure these are still in tight, and tighten if necessary		# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which color goes into which screw) so ensure these are still in tight, and tighten if necessary
	# Make sure the micro-SD card (on the underside of the core unit) is correctly seated in its holder. If you push it in a little it will pop out, but you should push it in again		# Make sure the micro-SD card (on the underside of the core unit) is correctly seated in its holder. If you push it in a little it will pop out, but you should push it in again

Mortice at 21:54, 28 February 2015

2015-02-28T21:54:53Z

← Older revision		Revision as of 21:54, 28 February 2015
Line 1:		Line 1:
	You should check over the ~~MortiSafe Pro core unit~~ you've got:		You should check over the set of 'magic' parts you've got:

			* The core circuit board (a Raspberry Pi) with relay unit on top and cable screwed into the relay unit. On the underside of the Raspberry Pi there's a micro-USB card held in a holder
			* A wifi unit which has a cover over one end (this can be discarded) to reveal a USB plug
			* An aerial which should be screwed into the end of the wifi unit
			* A USB power cable with clips half way along it
			* A micro USB adapter in a plastic cover. You shouldn't need this unless you have to do an upgrade in future.

	[[File:MSP_BoardCloseup.JPG\|700px]]		[[File:MSP_BoardCloseup.JPG\|700px]]

	~~This essentially has 5 parts:~~		Some things you should do and check when unpacking:

	* The core circuit board (a Raspberry Pi)
	* A relay unit, which sits on top of the core board
	* A wifi unit which plugs in at the side - this arrives as a stick (with a cap over the USB plug) and an aerial which screws onto the other end. You should screw the aerial on and plug it into any socket on the core unit
	* A white cable screwed into two of the screws on the relay unit
	* A USB power cable

	~~You should also find a micro USB adapter, you shouldn't need this unless you have to do an upgrade in future.~~

	Some things you should check when unpacking:

			# Screw the aerial into the wifi unit and plug that into the core unit (any socket)
	# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting		# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting
	# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which ~~colour~~ goes into which screw) so ensure these are still in tight, and tighten if necessary		# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which color goes into which screw) so ensure these are still in tight, and tighten if necessary
	# Make sure the micro-SD card (on the underside of the core unit) is correctly seated in its holder. If you push it in a little it will pop out, but you should push it in again		# Make sure the micro-SD card (on the underside of the core unit) is correctly seated in its holder. If you push it in a little it will pop out, but you should push it in again

Mortice at 21:06, 15 February 2015

2015-02-15T21:06:13Z

← Older revision		Revision as of 21:06, 15 February 2015
Line 24:		Line 24:
	# You'll also need to plug in an HDMI monitor cable later on, it fits into the socket next to the power socket at the top of the picture (you can only just see it on the picture)		# You'll also need to plug in an HDMI monitor cable later on, it fits into the socket next to the power socket at the top of the picture (you can only just see it on the picture)
	# There's a bunch of cable ties on the right of the core unit - these are there to guard the SD card and stop it getting bumped out when the parts are inside the safe		# There's a bunch of cable ties on the right of the core unit - these are there to guard the SD card and stop it getting bumped out when the parts are inside the safe

			You can now proceed to [[Wiring the digital safe to the MortiSafe Pro core unit wiring]].

Mortice at 16:50, 15 February 2015

2015-02-15T16:50:15Z

← Older revision		Revision as of 16:50, 15 February 2015
Line 7:		Line 7:
	* The core circuit board (a Raspberry Pi)		* The core circuit board (a Raspberry Pi)
	* A relay unit, which sits on top of the core board		* A relay unit, which sits on top of the core board
	* A wifi unit which plugs in at the side		* A wifi unit which plugs in at the side - this arrives as a stick (with a cap over the USB plug) and an aerial which screws onto the other end. You should screw the aerial on and plug it into any socket on the core unit
	* A white cable screwed into two of the screws on the relay unit		* A white cable screwed into two of the screws on the relay unit
	* A USB power cable		* A USB power cable

			You should also find a micro USB adapter, you shouldn't need this unless you have to do an upgrade in future.

	Some things you should check when unpacking:		Some things you should check when unpacking:
Line 15:		Line 17:
	# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting		# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting
	# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which colour goes into which screw) so ensure these are still in tight, and tighten if necessary		# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which colour goes into which screw) so ensure these are still in tight, and tighten if necessary
	# ~~The wifi unit is not attached when shipped, but take the cap off the end and plug it into any of~~ the ~~four USB sockets~~ on the ~~side~~ of the ~~main~~ unit		# Make sure the micro-SD card (on the underside of the core unit) is correctly seated in its holder. If you push it in a little it will pop out, but you should push it in again

	Some things of note:		Some things of note:
Line 21:		Line 23:
	# Later on you'll plug the power cable into the unit, you can see on this picture where it goes		# Later on you'll plug the power cable into the unit, you can see on this picture where it goes
	# You'll also need to plug in an HDMI monitor cable later on, it fits into the socket next to the power socket at the top of the picture (you can only just see it on the picture)		# You'll also need to plug in an HDMI monitor cable later on, it fits into the socket next to the power socket at the top of the picture (you can only just see it on the picture)
	# There's a bunch of cable ties on the right - these are there to guard the SD card and stop it getting bumped out when the parts are inside the safe		# There's a bunch of cable ties on the right of the core unit - these are there to guard the SD card and stop it getting bumped out when the parts are inside the safe

Mortice at 23:10, 4 February 2015

2015-02-04T23:10:14Z

← Older revision		Revision as of 23:10, 4 February 2015
Line 2:		Line 2:

	[[File:MSP_BoardCloseup.JPG\|700px]]		[[File:MSP_BoardCloseup.JPG\|700px]]

			This essentially has 5 parts:

			* The core circuit board (a Raspberry Pi)
			* A relay unit, which sits on top of the core board
			* A wifi unit which plugs in at the side
			* A white cable screwed into two of the screws on the relay unit
			* A USB power cable

			Some things you should check when unpacking:

			# Make sure the relay board is seated on the connector on the main board. If it's come loose in shipping, the relay board plugs into the line of pins on the main board. As seen on the picture, it goes on the right hand side of those pins so there's 7 pairs of pins left of it that are left exposed. The relay unit sits at an angle - the top end (as seen on pic) is kept off the main board by a nylon peg to stop short-circuiting
			# The white cable should be screwed into the screws marked 'A1' and 'COM1' on the relay board (doesn't matter which colour goes into which screw) so ensure these are still in tight, and tighten if necessary
			# The wifi unit is not attached when shipped, but take the cap off the end and plug it into any of the four USB sockets on the side of the main unit

			Some things of note:

			# Later on you'll plug the power cable into the unit, you can see on this picture where it goes
			# You'll also need to plug in an HDMI monitor cable later on, it fits into the socket next to the power socket at the top of the picture (you can only just see it on the picture)
			# There's a bunch of cable ties on the right - these are there to guard the SD card and stop it getting bumped out when the parts are inside the safe

Mortice: Created page with "You should check over the MortiSafe Pro core unit you've got: 700px"

2015-02-04T22:50:43Z

Created page with "You should check over the MortiSafe Pro core unit you've got: 700px"

New page

You should check over the MortiSafe Pro core unit you've got:

[[File:MSP_BoardCloseup.JPG|700px]]